The behaviour of jointed large-diameter reinforced concrete pipeline
Both centrifuge test and three-dimensional numerical simulation were performed to investigate the behaviour of a 1400-mm-diameter reinforced concrete
Contact Us
Both centrifuge test and three-dimensional numerical simulation were performed to investigate the behaviour of a 1400-mm-diameter reinforced concrete
Contact Us
Joints Ductile Iron Pipe is furnished with several different types of joints: push-on, mechanical, restrained, ball and socket, flanged, and grooved and shouldered joints. Typically, bridge crossings
Contact Us
Pipeline bridges may be made of steel, fiber reinforced polymer, reinforced concrete or similar materials. They may vary in size and style depending on the size of the pipeline being run. As there is
Contact Us
In former times during a construction of a transit gas pipeline of Eustream Company, it was necessary to overpass various route natural hurdles including rivers. In compliance with a
Contact Us
Replacing a pipeline structurally integrated into a bridge using traditional means is extremely expensive and in many cases impossible. Cured-in-place-Lining
Contact Us
At present, decisions regarding reinforcement of concrete pipes are primarily cost-driven. To consider other aspects, it is fundamental to identify and
Contact Us
FOREWORD This handbook covers a full range of topics and design examples intended to provide bridge engineers with the information needed to make knowledgeable decisions regarding the
Contact Us
Concrete Bridges These are quite literally bridges enabling cables and/or pipelines to cross each other, providing both protection and stabilisation. Designed in-house
Contact Us
The available size range of pipe piles and the stiffness that can be increased by increasing the pipe wall thickness has made them desirable for major bridge foundations. Pipe piles can also be driven with
Contact Us
This BDM provides general guidance on the design and detailing recommendations for pipe-pin connections between concrete bridge bent caps and columns based on a combination of Caltrans''
Contact Us
An increase of pipe wall thickness after the anchor block will not affect the force as the decrease in stress will be compensated for by the increase in the area of the metal. It is clear that this force is
Contact Us
Combining the requirements of the above railway concrete bridges for the reinforcement methods and the comparison from different angles, it can be
Contact Us
This document outlines the design philosophy for pipe bridge structures. It covers
Contact Us
Pipe pile bents require no concrete fill below the connection plug but require much thicker tubes compared to other alternatives. Reinforcing requirements for pipe pile bent plugs and for reinforced
Contact Us
This study evaluates the effectiveness of reinforcement measures for a corrugated steel pipe arch bridge subjected to differential settlement induced by underground mining. Using a ten
Contact Us
Complete reconditioning of the entire segment plus the reinforcement of the pipeline at the abutment wall was completed within a few days. Starline® Cured-in-Place
Contact Us
Thrust Blocks: The Complete 2026 Engineering Guide for Pipeline Stability Thrust Blocks are critical specialized structures designed to counteract the internal
Contact Us
Pipeline bridges are structures characterized by their triangular truss designs, which provide support and stability for pipelines. They have been used
Contact Us
Leaking joints on a 1.5 metre diameter pipe bridge and a 1.8 metre diameter pipe bridge undergo repair, followed by the entire
Contact Us
With the standard detailing practices for bridge piers previously mentioned (i.e., all column reinforcement extended and developed in the footing), along with identical design
Contact Us
HDSS and HP LOK restrained joint pipe are well suited for bridge applications. The deflection capabilities of these joints adapt easily to curves, radii and crowns of today''s bridges and move with
Contact Us
To address the issue of insufficient transverse connectivity in prestressed concrete box girder (PCB) bridges, this study investigates two
Contact Us
This paper aims to explore the technical and economic aspects associated with optimizing the performance of a pipeline bridge by modifying the constitutive elements.
Contact Us
Joints Ductile Iron pipe is furnished with several different types of joints: push-on, mechanical, restrained, ball and socket, flanged, and grooved and shouldered joints. Typically, bridge crossings
Contact Us
This report will be of interest to materials and bridge engineers, reinforced concrete corrosion specialists, and those concerned with the performance of reinforced and prestressed concrete bridges.
Contact Us+34 936 214 587
+49 89 452 38 217
Calle de la Tecnología 47, 08840 Viladecans, Barcelona, Spain