5 TIPS FOR RUNNING CABLES OUTDOORS

Fiber optic cables running along power poles have induced voltage

Fiber optic cables running along power poles have induced voltage

When a telecommunication cable is installed near very high-voltage transmission lines or railroad tracks electrified with alternating current, voltage is induced within the wire of a metal cable or in the metallic tension members of an optical fiber cable by either. One standard that has been developed by the Institute of Electrical and Electronics Enginee s, Inc (IEEE) is 1222, "IEEE Standard for All-Dielectric. This Technical Brochure describes the induction phenomena (inductive, capacitive and conductive) that can lead to presence of voltage and currents on disconnected cable systems. OPAC (optical power attached cable) is a type of fiber optic cable that is installed by attaching to a host conductor along overhead power lines. X is photons per second, lambda is wavelength, light speed is c (speed of light is reduced significantly in fiber ~30% reduction from vacuum speed), h term is Planck constant.

Read More
Cables can be run in cable trays outdoors

Cables can be run in cable trays outdoors

Despite widespread misinterpretation in the industry, standard tray-rated cable cannot run outside of the cable tray per the National Electrical Code (NEC) Sec. Type TC – Tray Cable – (NEC Article 336) –Power and control tray cable type TC is a factory assembly of two or more insulated conductors, with or without associated bare or covered grounding conductors, under a non-metallic jacket. There are many different types of cable tray including basket, ladder and solid-bottom. Cable trays allow easy access for maintenance, which is one of their greatest advantages over conduit. In the 2020 NEC ®, item 11 (multiconductor cable) was deleted so as not to give the impression that certain dry location cables such as type NM (nonmetallic sheathed cable) could be. Installation of Cable in Cable Trays involves precise routing on support systems, NEC/IEC compliance, grounding, ampacity derating, bend radius control, segregation of services, fire safety, labeling, and reliable cable management for industrial and commercial facilities.

Read More
Do cables running through cable trays need conduits

Do cables running through cable trays need conduits

TC-ER-rated cables can be installed in exposed runs outside the cable tray, up to 6 feet between the cable tray and connected equipment, and without conduit—provided that the cable is secured and protected from mechanical damage, per code. Conduit, on the other hand, is a rigid or flexible tube that provides additional mechanical protection and environmental. Cable trays are more preferable in large buildings or factories since they are not closed and can be readily repaired. But how do you decide which one is right for your project? In this post, we'll explore the key differences between cable trays vs conduits, highlight their pros and cons, and guide you toward the best choice based on your application. They provide a versatile and efficient solution for managing wires over long distances.

Read More
Danger Points When Replacing Fiber Optic Cables with Power Lines

Danger Points When Replacing Fiber Optic Cables with Power Lines

Besides the usual safety issues for all construction, generally covered under OSHA rules in the US (OSHA 10 and 30), fiber optics adds concerns for eye safety, chemicals, sparks from fusion splicing, disposal of fiber shards and more, covered in Part 1. As electrical professionals, most of us take fiber optic (FO) safety for granted. Fiber-optic cables are the backbone of modern connectivity—powering 5G networks, global internet backbones, and data center interconnections with near-light-speed data transmission. While these cables are engineered for durability (with some rated to last 25+ years), they are not invulnerable. Recognizing the potential safety hazard inherent in the installation and maintenance of optical fibers is crucial to mitigating risks of personal or property damage.

Read More
How about 10 Gigabit fiber optic cables

How about 10 Gigabit fiber optic cables

Multiple vendors introduced single-strand, bi-directional 10 Gbit/s optics capable of a single-mode fiber connection functionally equivalent to 10GBASE-LR or -ER, but using a single strand of fiber optic cable. To implement different 10GbE physical layer standards, many interfaces consist of a standard socket into which different physical (PHY) layer modules may be plugged. In SMF light follows a single path through the fiber while in MMF it takes multiple paths resulting in differential.

Read More

Get In Touch

Connect With Us

📱

Spain Office (HQ)

+34 936 214 587

🇪🇺

EU Technical Center

+49 89 452 38 217

📍

Headquarters (Spain)

Calle de la Tecnología 47, 08840 Viladecans, Barcelona, Spain